Materials science and engineering: A, Structural materials: properties, microstructure and processing, 0921-5093
Journal
| ISSNs | 0921-5093 |
|---|---|
| Additional searchable ISSN (electronic) | 1873-4936 |
101 - 110 out of 151Page size: 10
Publications / Theses
- 2009
- Published
Stress-controlled fatigue behaviour of micro-sized polycrystalline copper wires
Dehm, G., 2009, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 515, p. 71-78Research output: Contribution to journal › Article › Research › peer-review
- 2008
- Published
Competing Accommodation Mechanisms of the Martensite in Nanocrystalline NiTi Shape Memory Alloys
Waitz, T., Pranger, W., Antretter, T., Fischer, F. D. & Karnthaler, H-P., 2008, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 481-482, p. 479-483Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of chemical composition and manufacturing conditions on properties of NiTi shape memory alloys
Mehrabi, K., Bahmanpour, H., Shokuhfar, A. & Kneißl, A., 2008, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 481-482, p. 693-696Research output: Contribution to journal › Article › Research › peer-review
- Published
Influence of grain size on orientation changes during plastic deformation
Scheriau, S. & Pippan, R., 2008, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 493, p. 48-52Research output: Contribution to journal › Article › Research › peer-review
- Published
On the overaging behaviour of tool steel X38CrMoV5-3
Bischof, M., Staron, P., Caliskanoglu, Z. D., Leitner, H., Scheu, C. & Clemens, H., 2008, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 472, p. 148-152Research output: Contribution to journal › Article › Research › peer-review
- Published
Precipitation processes in a Mg–Zn–Sn alloy studied by TEM and SAXS
Rashkova, B., Prantl, W., Görgl, R., Keckes, J., Cohen, S., Bamberger, M. & Dehm, G., 2008, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. A494, p. 158-164Research output: Contribution to journal › Article › Research › peer-review
- 2007
- Published
Analysis of roughness-induced crack closure based on asymmetric crack-wake plasticity and size ratio effect
Pippan, R. & Pokluda, J., 2007, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. A462, p. 355-358Research output: Contribution to journal › Article › Research › peer-review
- Published
Changes in the mechanical properties of a pearlitic steel due to large shear deformation
Wetscher, F., Stock, R. & Pippan, R., 2007, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 445-446, p. 237-243Research output: Contribution to journal › Article › Research › peer-review
- Published
FIB damage of Cu and possible consequences for miniaturized mechanical tests
Kiener, D., Motz, C., Rester, M., Jenko, M. & Dehm, G., 2007, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 459, p. 262-272Research output: Contribution to journal › Article › Research › peer-review
- 2006
- Published
Annealing studies of nanocomposite Ti-Si-C thin films with respect to phase stability and tribological performance
Rester, M., Neidhardt, J., Eklund, P., Emmerlich, J., Ljungcrantz, H., Hultman, L. & Mitterer, C., 2006, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 429, p. 90-95Research output: Contribution to journal › Article › Research › peer-review
