Materials science and engineering: A, Structural materials: properties, microstructure and processing, ‎0921-5093

Journal

ISSNs0921-5093
Additional searchable ISSN (electronic)1873-4936
1 - 10 out of 151Page size: 10

Publications / Theses

  1. 2021
  2. Published

    Influence of high pressure torsion on microstructure evolution and mechanical properties of AZ80/SiC magnesium matrix composites

    Akbaripanah, F., Sabbaghian, M., Fakhar, N., Minárik, P., Veselý, J., Hung, P. T., Kapoor, G., Renk, O., Máthis, K., Gubicza, J. & Eckert, J., 5 Oct 2021, In: Materials Science and Engineering A. 826, 141916.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Copper and its effects on microstructure and correlated tensile properties of super duplex stainless steels

    Ressel, G., Gsellmann, M., Brandl, D., Landefeld, A., Keplinger, A., Zhang, Z., Maier-Kiener, V. & Schnitzer, R., 2021, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 2021, 821, p. 1-11

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Influence of thermomechanical fatigue loading conditions on the nanostructure of secondary hardening steels

    Hofinger, M., Seisenbacher, B., Landefeld, A., Ognianov, M., Leitner, H. & Schnitzer, R., 2021, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 2021, 802, p. 1-11

    Research output: Contribution to journal › Article › Research › peer-review

  5. Published

    Microstructure and mechanical properties of partially ferritic Q&P steels

    Kickinger, C., Suppan, C., Hebesberger, T., Schnitzer, R. & Hofer, C., 2021, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 2021, 815, p. 1-11

    Research output: Contribution to journal › Article › Research › peer-review

  6. 2020
  7. Published

    Mechanism of low temperature deformation in aluminium alloys

    Gruber, B., Weißensteiner, I., Kremmer, T., Grabner, F., Falkinger, G., Schökel, A., Spieckermann, F., Schäublin, R., Uggowitzer, P. & Pogatscher, S., 23 Sept 2020, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 795, 795, 11 p., 139935.

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    Balancing the strength and ductility of graphene oxide-carbon nanotube hybrid reinforced aluminum matrix composites with bimodal grain distribution

    Xu, Z. Y., Li, C. J., Wang, Z., Fang, D., Gao, P., Tao, J. M., Yi, J. H. & Eckert, J., 20 Aug 2020, In: Materials Science and Engineering A. 796.2020, 7 October, 7 p., 140067.

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Environmental hydrogen embrittlement associated with decohesion and void formation at soluble coarse particles in a cold-rolled Al–Cu based alloy

    Safyari, M., Moshtaghi, M. & Kuramoto, S., 9 Jul 2020, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing.

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    Evaluation of tensile and low-cycle fatigue properties at elevated temperatures in piston aluminum-silicon alloys with and without nano-clay-particles and heat treatment

    Azadi, M., Bahmanabadi, H., Gruen, F. & Winter, G., 11 May 2020, In: Materials Science and Engineering A. 788.2020, 24 June, 16 p., 139497.

    Research output: Contribution to journal › Article › Research › peer-review

  11. Published

    Effect of tempering and deep cryogenic treatment on microstructure and mechanical properties of Cr–Mo–V–Ni steel

    Yan, Z., Liu, K. & Eckert, J., 6 May 2020, In: Materials Science and Engineering A. 787.2020, 10 June, 8 p., 139520.

    Research output: Contribution to journal › Article › Research › peer-review

  12. Published

    Transformation-enhanced strength and ductility in a FeCoCrNiMn dual phase high-entropy alloy

    Zhang, T., Zhao, R. D., Wu, F. F., Lin, S. B., Jiang, S. S., Huang, Y. J., Chen, S. H. & Eckert, J., 7 Apr 2020, In: Materials Science and Engineering A. 780.2020, 7 April, 7 p., 139182.

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1 2 3 4 5 6 7 8 ...16 Next
View graph of relations