Materials science and engineering: A, Structural materials: properties, microstructure and processing, ‎0921-5093

Journal

ISSNs0921-5093
Additional searchable ISSN (electronic)1873-4936
61 - 70 out of 151Page size: 10

Publications / Theses

  1. 2015
  2. Published

    Characterization of the high temperature deformatin behavior of two intermetallic TiAl-Mo alloys

    Godor, F., Werner, R., Lindemann, J., Clemens, H. & Mayer, S., 2015, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 648, p. 208-216

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Elevated temperature mechanical properties of novel ultra-fine grained Cu-Nb composites

    Primorac, M-M., Abad, M. D., Hosemann, P., Kreuzeder, M., Maier, V. & Kiener, D., 2015, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 625, p. 296-302

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Incremental high pressure torsion as a novel severe plastic deformation process: Processing features and application to copper

    Hohenwarter, A., 2015, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 626, p. 80-85

    Research output: Contribution to journal › Article › Research › peer-review

  5. 2014
  6. Published

    Yield strength prediction in Ni-base alloy 718Plus based on thermo-kinetic precipitation simulation

    Ahmadi, M. R., Povoden-Karadeniz, E., Whitmore, L., Stockinger, M., Falahati, A. & Kozeschnik, E., 1 Jul 2014, In: Materials Science and Engineering A. 608, p. 114-122 9 p.

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Comparison of microstructural crack paths between hypo-eutectic Al-Si-Cu and Al-Si-Mg cast alloys in high plasticity regimes under rotating bending

    Huter, P., Winter, G., Renhart, P., Schwab, M., Oberfrank, S., Grün, F. & Stauder, B., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 618, p. 578-585

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    Hot-working behavior of an advanced intermetallic multi-phase gamma-TiAl based alloy

    Schwaighofer, E., Clemens, H., Lindemann, J., Stark, A. & Mayer, S., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 614, p. 297-310

    Research output: Contribution to journal › Article › Research › peer-review

  9. Published

    Microstructural investigation of thermally aged nickel-based superalloy 718Plus

    Whitmore, L., Ahmadi, M. R., Stockinger, M., Povoden-Karadeniz, E., Kozeschnik, E. & Leitner, H., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 594, p. 253-259

    Research output: Contribution to journal › Article › Research › peer-review

  10. Published

    The microstructure of heat-treated nickel-based superalloy 718Plus

    Whitmore, L., Ahmadi, M. R., Guetaz, L., Leitner, H., Povoden-Karadeniz, E., Stockinger, M. & Kozeschnik, E., 2014, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 610, p. 39-45

    Research output: Contribution to journal › Article › Research › peer-review

  11. 2013
  12. Published

    The influence of microstructure and operating temperature on the fatigue endurance of hot forged Inconel (R) 718 components

    Maderbacher, H., Oberwinkler, B., Gänser, H-P., Tan, W., Rollett, M. & Stoschka, M., 15 Nov 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 585, p. 123-131

    Research output: Contribution to journal › Article › Research › peer-review

  13. Published

    Activation Parameters for Deformation of Ultrafine-Grained Aluminium as Determined by Indentation Strain Rate Jumps at Elevated Temperature

    Wheeler, J. M., Maier, V., Durst, K., Göken, M. & Michler, J., 2013, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 585, p. 108-113

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1...3 4 5 6 7 8 9 10 ...16 Next
View graph of relations