Department Polymer Engineering and Science
Organisational unit: Departments & Institutes
221 - 230 out of 3,454Page size: 10
Publications / Theses
- 2019
- Published
Vorhersage des Ermüdungsverhaltens von Verbundwerkstoffen
Drvoderic, M., 12 Nov 2019. 1 p.Research output: Contribution to conference › Poster › Research
- Published
Destroying or Enhancing the Mechanical Properties of Carbon Fibre Filled PA12 filaments for Additive Manufacturing?
Holzer, C., Gonzalez-Gutierrez, J., Cano Cano, S., Schuschnigg, S., Arbeiter, F., Liu, D., Wuzella, G. H. & Lammer, H., 7 Nov 2019, p. 59-59. 1 p.Research output: Contribution to conference › Abstract › peer-review
- Published
Fracture mechanics description of the defect in rolling cylinder
Dlhy, P., Poduška, J., Berer, M., Gosch, A., Pinter, G. G. & Hutař, P., 4 Nov 2019.Research output: Contribution to conference › Paper › peer-review
- Published
Soil Load on Plastic Pipe and its Influence on Lifetime
Poduška, J., Hutař, P., Frank, A., Kučera, J., Sadílek, J., Pinter, G. & Náhlík, L., 1 Nov 2019, In: Strojnícky časopis = Journal of mechanical engineering. 69, 3, p. 101-106 6 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Processing Fiber-Reinforced Polymers: Specific Wear Phenomena Caused by Filler Materials
Blutmager, A., Spahn, T., Varga, M., Friesenbichler, W., Riedl, H. & Mayrhofer, P. H., 18 Oct 2019, In: Polymer engineering and science. 60.2020, 1, p. 78-85 8 p.Research output: Contribution to journal › Article › Research
- Published
Influence of stearic acid in feedstocks for FFF and PIM
Kukla, C., Cano Cano, S., Holzer, C. & Gonzalez-Gutierrez, J., 16 Oct 2019.Research output: Contribution to conference › Paper › peer-review
- Published
Material extrusion‐based additive manufacturing of polypropylene: A review on how to improve dimensional inaccuracy and warpage
Spörk, M., Holzer, C. & Gonzalez-Gutierrez, J., 16 Oct 2019, In: Journal of Applied Polymer Science. 137, 12, 16 p., 48545.Research output: Contribution to journal › Literature review › peer-review
- Published
Simultaneous Structural and Material Optimisation
Lang, M. C., 16 Oct 2019.Research output: Contribution to conference › Abstract › peer-review
- Published
Cyclic plastic deformation of rails in rolling/sliding contact –quasistatic FE calculations using different plasticity models
Pletz, M., Meyer, K. A., Künstner, D., Scheriau, S. & Daves, W., 15 Oct 2019, In: Wear. 436-437, 202992.Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
3D-Printing of High-κ Thiol-Ene Resins with Spiro-Orthoesters as Anti-Shrinkage Additive
Marx, P., Romano, A., Roppolo, I., Chemelli, A., Mühlbacher, I., Kern, W., Chaudhary, S., Andritsch, T., Sangermano, M. & Wiesbrock, F., 14 Oct 2019, (E-pub ahead of print) In: Macromolecular materials and engineering. 304.2019, 12, 10 p., 1900515.Research output: Contribution to journal › Article › Research › peer-review
