Florian Grün
21 - 30 out of 341Page size: 10
Publications / Theses
- 2020
- Published
Tribological investigations with near eutectic AlSi alloys found in engine vane pumps – Characterization of the material tribo-functionalities
Summer, F., Pusterhofer, M., Grün, F. & Gódor, I., 1 Feb 2020, In: Tribology International. 146.2020, June, 13 p., 106236.Research output: Contribution to journal › Article › Research › peer-review
- Published
Assessment of Shaft Surface Structures on the Tribological Behavior of Journal Bearings by Physical and Virtual Simulation
Pusterhofer, M., Summer, F., Maier, M. & Grün, F., 15 Jan 2020, In: Lubricants. 8.2020, 1, 16 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Close-to-Application Test Methodology Validated by a Baseline Study for Novel Bearing Developments in Aircraft Turbines
Renhart, P., Summer, F., Grun, F. & Eder, A., 9 Jan 2020, In: Lubricants. 8.2020, 1, p. 1-14 14 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Friction and Wear Performance of Various Polymer Coatings for Journal Bearings under Stop Start Sliding
Summer, F., Grun, F. & Ravenhill, E. R., 1 Jan 2020, In: Lubricants. 8.2020, 1, 14 p., 1.Research output: Contribution to journal › Article › Research › peer-review
- Published
Material behaviour of a dual hardening steel under thermomechanical loading
Seisenbacher, B., Hofinger, M., Winter, G. & Grün, F., Jan 2020, In: Fatigue & fracture of engineering materials & structures : Fatigue and fracture of engineering materials and structures. 43, 1, p. 191-200 10 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Effect of surface layer on the fatigue strength of additively manufactured 17-4 PH steel
Leitner, M., Schneller, W., Springer, S. & Grun, F., 2020.Research output: Contribution to conference › Paper
- Published
Numerical Fatigue Analysis of Induction-Hardened and Mechanically Post-Treated Steel Components
Leitner, M., Aigner, R. & Grun, F., 2020, Advances in CAD/CAM/CAE Technologies. Multidisciplinary Digital Publishing Institute (MDPI)Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research
- 2019
- Published
Development of a Model Test System for a Piston Ring/Cylinder Liner-Contact with Focus on Near-to-Application Seizure Behaviour
Pusterhofer, M., Summer, F., Wuketich, D. & Grun, F., 22 Nov 2019, In: Lubricants. 7.2019, 12, p. 104-115 12 p., 104.Research output: Contribution to journal › Article › Research › peer-review
- Published
Influencing factors on the fatigue strength of selectively laser melted structures
Schneller, W., Leitner, M., Springer, S., Beter, F. & Grun, F., 20 Nov 2019.Research output: Contribution to conference › Poster › Research
- Published
Effect of Post Treatment on the Microstructure, Surface Roughness and Residual Stress Regarding the Fatigue Strength of Selectively Laser Melted AlSi10Mg Structures
Schneller, W., Leitner, M., Pomberger, S., Springer, S., Beter, F. & Grun, F., 16 Oct 2019, In: Journal of Manufacturing and Materials Processing. 2019, 3(4), 21 p., 89.Research output: Contribution to journal › Article › Research › peer-review
