Department Polymer Engineering and Science

Organisational unit: Departments & Institutes

1731 - 1740 out of 3,454Page size: 10

Publications / Theses

  1. 2013
  2. Published

    IMPACT OF SINGLE AND DUAL PRESSURE BUTT-WELDING PROCEDURES ON THE RELIABILITY OF PE 100 PIPE WELDS

    Arbeiter, F., Pinter, G. & Frank, A., 2013, Proceedings of Eurotec 2013.

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  3. Published

    Impact of varying between single and dual pressure butt-welding procedures for small scale pipes on short- and long-term fracture properties of PE 100 pipe welds

    Arbeiter, F., 2013.

    Research output: Contribution to conference › Presentation › Research

  4. Published

    Improvement of light shielding performance of thermotropic glazings by adaption of material composition and curing parameters

    Weber, A. & Resch, K., 2013, Proceedings of the Austrian-Slovenian Polymer Meeting 2013. p. 132-133

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  5. Published

    Influence of Chain Extender on the Foaming Behavior and on the Mechanical Properteis of Physically Foamed PLA

    Mostafa, H., Geißler, B., Uray, A., Laske, S., Holzer, C. & Langecker, G., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  6. Published

    Influence of chain extender on the foaming behaviour and the mechanical properties of physically foamed PLA

    Geißler, B., Mostafa, H., Uray, A., Laske, S., Holzer, C. & Langecker, G., 2013, The 29th International Conference of The Polymer Processing Society (PPS-29). p. 120-125

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  7. Published

    Influence of different fillers on the processing behaviour and mechanical properties of physically foamed polyethylene

    Geißler, B., Laske, S., Holzer, C. & Langecker, G., 2013, The 29th International Conference of The Polymer Processing Society (PPS-29). p. 129-134

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  8. Published

    Influence of material condition on processing of rubber compounds and its representation in simulation

    Fasching, M., Friesenbichler, W. & Berger, G., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013. p. 75-77

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  9. Published

    Influence of Mold Surface Temperature on Polymer Part Warpage in Rapid Heat Cycle Molding

    Berger, G., Pacher, G., Gruber, D. P., Pichler, A. & Friesenbichler, W., 2013, 29th International Conference of the Polymer Processing Society. p. 49-49

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  10. Published

    Influence of particle size and particle shape on mechanical, rheological and thermal properties of polyproyplene / aluminum composites

    Holzer, C., 2013, Proceedings of the 29th International Conference of the Polymer Processing Society. p. xxx-xxx

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  11. Published

    INFLUENCE OF PROCESS SETTINGS ON THE TOPOGRAPHY OF SINK MARKS

    Pacher, G., Berger, G., Gruber, D. P. & Friesenbichler, W., 2013, ADVANCES IN PLASTICS TECHNOLOGY - Conference Papers. Gliwice, Polen, p. Paper No. 31

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

Previous 1...170 171 172 173 174 175 176 177 ...346 Next
View graph of relations

Contact information

Otto Glöckel-Straße 2, 8700 Leoben
  • Main phone number: +43 3842 402 2301