Walter Friesenbichler

(Former)

141 - 160 out of 278Page size: 20

Publications / Theses

  1. 2013
  2. Published

    Application of deflectometry for surface inspection of high-­‐glossy injection-­‐molded facing parts

    Macher, J., Gruber, D. P., Berger, G. & Friesenbichler, W., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013: ASPM 2013. Ljubljana, p. 93-95

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  3. Published

    Application of D-­optimal design of experiments on process optimization of an automotive part

    Berger, G., Luger, H.-J., Friesenbichler, W., Beytollahi, I., Gierth, M. & Filz, P., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013. p. 106-108

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  4. Published

    Ausnutzung der Scher- und Dehnerwärmung zur Heizzeitverkürzung; bei der Verarbeitung von Elastomeren

    Perko, L., Friesenbichler, W. & Fasching, M., 2013, In: Österreichische Kunststoff-Zeitschrift. p. 252-254

    Research output: Contribution to journal › Article › Research › peer-review

  5. Published

    Ausnutzung der Scher- und Dehnerwärmung zur Heizzeitverkürzung; bei der Verarbeitung von Elastomeren

    Perko, L., Friesenbichler, W. & Fasching, M., 2013, In: GAK (Gummi Fasern Kunststoffe). 66, p. 622-624

    Research output: Contribution to journal › Article › Research › peer-review

  6. Published

    Correlation between Rheotens Measurements and Reinforcement of Polymer Nanocomposites in the Injection Molding Compounder

    Battisti, M., Duretek, I., Friesenbichler, W., Guttmann, P. & Pinter, G., 2013, 1st International Conference on Rheology and Modelling of Materials - Book of Abstracts. p. 39-39

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  7. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modeling on Prediction Quality

    Luger, H.-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  8. Published

    Deformation Analysis of an Automotive Part by Injection Molding Simulation: Influence of Material Data and Mold Modelling on Prediction Quality

    Luger, H.-J., Berger, G., Müller, F., Friesenbichler, W., Beytollahi, I. & Filz, P., 2013, 29th International Conference of the Polymer Processing Society. p. 59-59

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  9. Published

    Die Wirkung dynamischer Werkzeugtemperierung auf die Oberflächenqualität von Kunststoffteilen

    Pacher, G., Berger, G., Friesenbichler, W. & Gruber, D. P., 2013, 22. Leobener Kunststoff-Kolloquium: Oberlfächen und Grenzflächen in der Polymertechnologie. p. 101-110

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  10. Published

    Elongational viscosity of rubber compounds and improving corresponding models

    Perko, L., Friesenbichler, W., Obendrauf, W., Buchebner, V. & Chaloupka, G., 2013, In: Advances in production engineering & management. 8, p. 126-133

    Research output: Contribution to journal › Article › Research › peer-review

  11. Published

    Influence of material condition on processing of rubber compounds and its representation in simulation

    Fasching, M., Friesenbichler, W. & Berger, G., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013. p. 75-77

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  12. Published

    Influence of Mold Surface Temperature on Polymer Part Warpage in Rapid Heat Cycle Molding

    Berger, G., Pacher, G., Gruber, D. P., Pichler, A. & Friesenbichler, W., 2013, 29th International Conference of the Polymer Processing Society. p. 49-49

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  13. Published

    INFLUENCE OF PROCESS SETTINGS ON THE TOPOGRAPHY OF SINK MARKS

    Pacher, G., Berger, G., Gruber, D. P. & Friesenbichler, W., 2013, ADVANCES IN PLASTICS TECHNOLOGY - Conference Papers. Gliwice, Polen, p. Paper No. 31

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  14. Published

    In-Mold Sensor Concept to calculate process-specific Rheological Properties

    Pacher, G., Berger, G., Friesenbichler, W., Gruber, D. P. & Macher, J., 2013, 29th International Conference of the Polymer Processing Society. p. 48-48

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  15. Published

    Kosten reduzieren durch systematische Entwicklungsprozesse

    Friesenbichler, W., Gröger, T., Vetschera, R. & Hopmann, C., 2013, In: Kunststoffe. p. 50-53

    Research output: Contribution to journal › Article › Research › peer-review

  16. Published

    Model for the prediction of elegational heating rubber compounds in conical dies

    Perko, L., Fasching, M. & Friesenbichler, W., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  17. Published

    Model for the prediction of elegational heating rubber compounds in conical dies

    Perko, L., Fasching, M. & Friesenbichler, W., 2013, THE PROCEEDINGS OF THE AUSTRIAN – SLOVENIAN POLYMER MEETING 2013. p. 258-259

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  18. Published

    MODEL FOR THE PREDICTION OF SHEAR AND ELONGATIONAL HEATING OF RUBBER COMPOUNDS IN CONICAL DIES

    Perko, L., Fasching, M. & Friesenbichler, W., 2013.

    Research output: Contribution to conference › Poster › Research › peer-review

  19. Published

    More Gloss, Fewer Weld Lines With Variothermal Molding

    Berger, G., Roock, S., Steinbichler, G., Gießauf, J., Gruber, D. P. & Friesenbichler, W., 2013, In: Plastics technology. 59, 3, p. 30, 60-35, 62

    Research output: Contribution to journal › Article › Research › peer-review

  20. Published

    MULTI-FUNCTIONAL INJECTION MOLD FOR EXAMINING THE INFLUENCE OF RAPID HEAT CYCLE MOLDING ON POLYMER MORPHOLOGY

    Pacher, G., Berger, G. & Friesenbichler, W., 2013, Tagungsband der 3. Tagung Innovation Messtechnik. p. 25-30

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  21. Published

    NEW METHODS FOR QUALITY CONTROL OF INJECTION-MOLDED PARTS

    Macher, J., Gruber, D. P., Berger, G. & Friesenbichler, W., 2013, ANTEC 2013 Conference and Tradeshow. p. 1-4

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

Previous 1...4 5 6 7 8 9 10 11 ...14 Next
View graph of relations

Latest Research Output

View more (278)