Tanja Lube

1 - 50 out of 139Page size: 50

Publications / Theses

  1. 2021
  2. E-pub ahead of print

    Distribution distortion in the statistical analysis of strength data when using multiple specimen batches

    Salem, J. A., Lube, T., Béhar-Lafenêtre, S. & Baker, E. H., 2 Sept 2021, (E-pub ahead of print) In: Journal of the European Ceramic Society.

    Research output: Contribution to journal › Article › Research › peer-review

  3. Published

    Comparison of biaxial strength measured with the Ball-on-Three-Balls- and the Ring-on-Ring-test

    Staudacher, M., Lube, T., Schlacher, J. & Supancic, P., 17 Apr 2021, In: Open ceramics. 6.2021, June, 10 p., 100101.

    Research output: Contribution to journal › Article › Research › peer-review

  4. Published

    Fracture Toughness Measurement

    Lube, T., 2021, Encyclopedia of Materials: Technical Ceramics and Glasses. Oxford: Elsevier, Vol. 1. p. 762-774

    Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research

  5. 2020
  6. Published

    Strength of additive manufactured alumina

    Schlacher, J., Lube, T., Harrer, W., Mitteramskogler, G., Schwentenwein, M., Danzer, R. & Bermejo, R., 30 Jul 2020, In: Journal of the European Ceramic Society. 40, 14, p. 4737-4745

    Research output: Contribution to journal › Article › Research › peer-review

  7. Published

    Influence of the Infill Orientation on the Properties of Zirconia Parts Produced by Fused Filament Fabrication

    Cano, S., Lube, T., Huber, P., Gallego, A., Naranjo, J. A., Berges, C., Schuschnigg, S., Herranz, G., Kukla, C., Holzer, C. & Gonzalez-Gutierrez, J., 15 Jul 2020, In: Materials. 13, 14, 3158.

    Research output: Contribution to journal › Article › Research › peer-review

  8. Published

    Influence of WC-Co hard metal microstructure on defect density, initiation and propagation kinetics of fatigue cracks starting at intrinsic and artificial defects under a negative stress ratio

    Klünsner, T., Lube, T., Gettinger, C., Walch, L. & Pippan, R., 12 Feb 2020, In: Acta materialia. 188, p. 30-39

    Research output: Contribution to journal › Article › Research › peer-review

  9. 2019
  10. Published

    Strength of Lithography-Based Alumina

    Schlacher, J. C., Lube, T., Mitteramskogler, G., Schwentenwein, M. & Danzer, R., 9 Sept 2019.

    Research output: Contribution to conference › Poster › Research › peer-review

  11. Published

    Biaxiale Festigkeitsprüfung von Keramiken

    Supancic, P. H., Lube, T. & Danzer, R., 13 Feb 2019.

    Research output: Contribution to conference › Poster › Research › peer-review

  12. Published

    Festigkeit von additiv gefertigtem Aluminiumoxid

    Lube, T., Schlacher, J. C., Harrer, W. S., Danzer, R., Mitteramslkogler, G. & Schwentenwein, M., 13 Feb 2019.

    Research output: Contribution to conference › Poster › Research › peer-review

  13. Published

    Fatigue behaviour of WC-Co hard metal under stress ratio and effectively loaded volume relevant to metalworking tool failure

    Klünsner, T., Jonke, M., Supancic, P., Gettinger, C., Krobath, M., Lube, T., Marsoner, S. & Glätzle, J., 4 Jan 2019, In: International Journal of Refractory Metals and Hard Materials. 80, p. 97-103 7 p.

    Research output: Contribution to journal › Article › Research › peer-review

  14. Published

    Fracture toughness of Silicon Nitride Measured by the Surface Crack in Flexure (SCF) Test Method

    Nindhia, T. G. T. & Lube, T., 2019, In: IOP Conference Series: Materials Science and Engineering. 622, 012001.

    Research output: Contribution to journal › Article › Transfer › peer-review

  15. Published

    Single Edge Precrack V-Notched Beam (SEPVNB) Fracture Toughness Testing on Silicon Nitride

    Nindhia, T. G. T. & Lube, T., 2019, In: Materials Science Forum. p. 205-209

    Research output: Contribution to journal › Article › Research › peer-review

  16. 2018
  17. Published

    Corrigendum to "Surface Crack in Tension or in Bending - A Reassessment of the Newman and Raju Formula in Respect to Fracture Toughness Measurements in Brittle Materials" [J. Eur. Ceram. Soc. 32 (8) (2012) 1491–1501]

    Strobl, S., Supancic, P., Lube, T. & Danzer, R., 2018, In: Journal of the European Ceramic Society. p. 355-358 4 p.

    Research output: Contribution to journal › Article › Research › peer-review

  18. Published

    Fracture Toughness (KIC) of Lithography Based Manufactured Alumina Ceramic

    Nindhia, T. G. T., Schlacher, J. C. & Lube, T., 2018, In: IOP Conference Series: Materials Science and Engineering. 012022.

    Research output: Contribution to journal › Article › Research › peer-review

  19. Published

    Fracture toughness of silicon nitride balls via thermal shock

    Strobl, S., Adlmann, F. A., Supancic, P., Lube, T., Danzer, R. & Schöppl, O., 2018, In: Journal of the European Ceramic Society. p. 1278–1287

    Research output: Contribution to journal › Article › Research › peer-review

  20. Published

    Fracture toughness testing of biomedical ceramic-based materials using beams, plates and discs

    Belli, R., Wendler, M., Petschelt, A., Lube, T. & Lohbauer, U., 2018, In: Journal of the European Ceramic Society. 38, 16, p. 5533-5544 12 p.

    Research output: Contribution to journal › Article › Research › peer-review

  21. Published

    Mechanische Eigenschaften von gedruckten Keramiken

    Lube, T., Schlacher, J., Harrer, W., Danzer, R., Mitteramskogler, G. & Schwentenwein, M., 2018, Praktische Metallographie Sonderband. Vol. 52. p. 229-234

    Research output: Chapter in Book/Report/Conference proceeding › Conference contribution

  22. 2017
  23. Published

    Additive Fertigung von Keramiken

    Lube, T. & Harrer, W. S., 13 Nov 2017.

    Research output: Contribution to conference › Poster › Transfer

  24. Published

    Strength of Al2O3-Ceramic Produced by the LCM Additive Manufacturing Technology

    Lube, T., Schlacher, J. C., Harrer, W. S., Mitteramskogler, G., Schwentenwein, M. & Danzer, R., 12 Jul 2017.

    Research output: Contribution to conference › Poster › Research › peer-review

  25. Published

    Chairside CAD/CAM materials. Part 2: flexural strength testing

    Belli, R., Wendler, M., Petschelt, A., Mevec, D., Lube, T., Harrer, W., Danzer, R. & Lohbauer, U., 2017, In: Dental Materials. 33, 1, p. 99-109 11 p.

    Research output: Contribution to journal › Article › Research › peer-review

  26. Published

    Fractography of zirconia-specimens made using additive manufacturing (LCM) technology

    Harrer, W. S., Schwentenwein, M., Lube, T. & Danzer, R., 2017, In: Journal of the European Ceramic Society. 37, p. 4331-4338

    Research output: Contribution to journal › Article › Research › peer-review

  27. Published

    Lifetime Prediction of Ceramic Components - A Case Study on Hybrid Rolling Contact

    Khader, I., Rasche, S., Lube, T., Raga, R., Degenhardt, U. & Kailer, A., 2017, In: Engineering Fracture Mechanics. 169, p. 292-308 17 p.

    Research output: Contribution to journal › Article › Research › peer-review

  28. Published

    Strength behaviour of etched Zerodur®

    Lube, T. & Béhar-Lafenêtre, S., 2017, In: Journal of the European Ceramic Society. 37

    Research output: Contribution to journal › Article › Research › peer-review

  29. Published

    Surface strength of balls made of five structural ceramic materials evaluated with the Notched Ball Test (NBT)

    Strobl, S., Lube, T., Supancic, P., Schöppl, O. & Danzer, R., 2017, In: Journal of the European Ceramic Society. 37, 15, p. 5065-5070 6 p.

    Research output: Contribution to journal › Article › Research › peer-review

  30. 2016
  31. Published

    Messung der Bruchzähigkeit mit dem B3B-Test

    Lube, T. & Rasche, S., 4 Apr 2016.

    Research output: Contribution to conference › Presentation › Research › peer-review

  32. Published

    Analysis of the effective thermoelastic properties and stress fields in silicon nitride based on EBSD data

    Othmani, Y., Böhlke, T., Lube, T., Fellmeth, A., Chlup, Z., Colonna, F. & Hashibon, A., 2016, In: Journal of the European Ceramic Society. 36, p. 1109-1125 17 p.

    Research output: Contribution to journal › Article › Research › peer-review

  33. Published

    A New Fracture Toughness Test for Ceramic Discs and Plates

    Lube, T., Rasche, S. & Nindhia, T. G. T., 2016.

    Research output: Contribution to conference › Poster › Research › peer-review

  34. Published

    B3B-KIc fracture toughness test – geometric function formulae for semi-elliptical surface cracks in bi-axial bending

    Lube, T., Rasche, S. & Nindhia, T. G. T., 2016, In: Journal of the American Ceramic Society. 99, 1, p. 249–256

    Research output: Contribution to journal › Article › Research › peer-review

  35. Published

    Biaxial strength testing of dental CAD/CAM block materials

    Wendler, M., Belli, R., Petschelt, A., Mevec, D., Harrer, W., Lube, T., Danzer, R. & Lohbauer, U., 2016.

    Research output: Contribution to conference › Poster › Research › peer-review

  36. Published

    Die Messung der Bruchzähigkeit von Keramiken: State of the Art und neue Methoden

    Danzer, R. & Lube, T., 2016.

    Research output: Contribution to conference › Presentation › Research › peer-review

  37. Published

    Fracture toughness of Ceramic Discs and Plates

    Lube, T., Rasche, S. & Nindhia, T. G. T., 2016.

    Research output: Contribution to conference › Poster › Research › peer-review

  38. Published

    Recent Advances on Fast Fracture Strength of Zerodur® for Space Applications

    Béhar-Lafenêtre, S., Lube, T. & Ait-Zaid, S., 2016.

    Research output: Contribution to conference › Presentation › Research › peer-review

  39. Published

    Recent Andvances on Fast Fracture Strength of Zerodur® for Space Applications

    Béhar-Lafenêtre, S., Lube, T. & Ait-Zaid, S., 2016.

    Research output: Contribution to conference › Paper › peer-review

  40. 2015
  41. Published

    Vertraulicher Bericht: Endbericht (P048-F-02-03)

    Preis, W., Bucher, E., Sitte, W., Egger, A., Perz, M., Schrödl, N., Waldhäusl, J., Lube, T., Kusnezoff, M., Lawlor, V. & Werl, M., 3 Dec 2015

    Research output: Book/Report › Commissioned report › Research

  42. Published

    Vertraulicher Bericht: Publizierbarer Endbericht (P048-F-02-03)

    Preis, W., Bucher, E., Sitte, W., Egger, A., Perz, M., Schrödl, N., Waldhäusl, J., Lube, T., Kusnezoff, M., Lawlor, V. & Werl, M., 3 Dec 2015

    Research output: Book/Report › Commissioned report › Research

  43. Published

    The importance of mechanical testing for design with ceramics

    Lube, T., 7 Oct 2015.

    Research output: Contribution to conference › Paper › peer-review

  44. Published

    Determination of fracture toughness of small discs using the ball-on-three-balls test

    Lube, T., Rasche, S., Nindhia, T. G. T. & Strobl, S., 22 Jun 2015.

    Research output: Contribution to conference › Presentation › Research › peer-review

  45. Published

    Bruchzähigkeitsmessung an keramischen Scheiben und Platten

    Lube, T., Rasche, S. & Nindhia, T. G. T., 9 Apr 2015.

    Research output: Contribution to conference › Poster › Research

  46. Published

    Macroscopic damage modeling for silicon nitride

    Ruck, J., Othmani, Y., Lube, T., Khader, I., Kailer, A. & Böhlke, T., 2015, In: Proceedings in applied mathematics and mechanics. 15, p. 147-148 2 p.

    Research output: Contribution to journal › Article › Research › peer-review

  47. Published

    On the Development of Experimental Methods for the Determination of Fracture Toughness Parameters of Ceramics

    Danzer, R., Lube, T. & Rasche, S., 2015, Recent Trends in Fracture and Damage Mechanics. Hütter, G. & Zybell, L. (eds.). Heidelberg: Springer, p. 197-214 18 p.

    Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research

  48. Published

    Testing Methods on Ceramic Rolling Elements for Hybrid Bearings

    Schöppl, O. & Lube, T., 2015, In: Materials Performance and Characterization. 4, 1

    Research output: Contribution to journal › Article › Research › peer-review

  49. 2014
  50. Published

    Vertraulicher Zwischenbericht vom 25.4.2014 (P048-F-02-03)

    Preis, W., Bucher, E., Egger, A., Perz, M., Schrödl, N., Waldhäusl, J., Sitte, W., Lube, T., Lawlor, V., Janics, A., Hochenauer, C. & Kusnezoff, M., 25 Apr 2014

    Research output: Book/Report › Commissioned report › Transfer

  51. Published

    Apparent R-curve of Laminates with Strong Interfaces made from Al2O3 and Al2O3/ZrO2-Composites

    Lube, T., 2014, Encyclopedia of Thermal Stresses. p. 6643-6647

    Research output: Chapter in Book/Report/Conference proceeding › Chapter › Research

  52. Published

    Ber-08-2014-RoLiCer: RoLiCer Deliverable 2.1: Tool for Calculation of Stress Intensity Factors

    Rasche, S. & Lube, T., 2014

    Research output: Book/Report › Commissioned report › Transfer

  53. Published

    Ber-28-2014-RoLiCer: RoLiCer Deliverable 8.4: Workshop “metal forming” September 2014

    Lube, T., 2014

    Research output: Book/Report › Commissioned report › Transfer

  54. Published

    Ber-34-2014-RoLiCer: RoLiCer Deliverable 6.3: Optimal surface finish for ceramic balls

    Lube, T., Harrer, W. & Vieillard, C., 2014

    Research output: Book/Report › Commissioned report › Transfer

  55. Published

    Ber-35-2014-ELTSECCS: Deliverable: 4.1 Materialparameter als Funktion unterschiedlicher Betriebsbedingungen

    Lube, T. & Harrer, W., 2014

    Research output: Book/Report › Commissioned report › Transfer

  56. Published

    Ber-57-2014-RoLiCer: RoLiCer Deliverable 5.6: Industrial Field test: Wire Rolling Analysis and documentation

    Harrer, W. & Lube, T., 2014

    Research output: Book/Report › Commissioned report › Transfer

  57. Published

    Ber-66-2014-RoLiCer: RoLiCer @ MUL: Periodic Report (Month 36)

    Lube, T. & Rasche, S., 2014

    Research output: Book/Report › Commissioned report › Transfer

  58. Published

    Determination of strength and fracture toughness of small ceramic discs using the small punch test and the ball-on-three-balls test

    Rasche, S., Strobl, S., Kuna, M., Bermejo Moratinos, R. & Lube, T., 2014, In: Procedia Materials Science. p. 961-966

    Research output: Contribution to journal › Article › Research › peer-review

Previous 1 2 3 Next
View graph of relations

Contact

Phone: 4111

Latest Research Output

View more (139)