Materials science and engineering: A, Structural materials: properties, microstructure and processing, 0921-5093
Journal
| ISSNs | 0921-5093 |
|---|---|
| Additional searchable ISSN (electronic) | 1873-4936 |
41 - 50 out of 151Page size: 10
Publications / Theses
- Published
Elevated temperature mechanical properties of novel ultra-fine grained Cu-Nb composites
Primorac, M.-M., Abad, M. D., Hosemann, P., Kreuzeder, M., Maier, V. & Kiener, D., 2015, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 625, p. 296-302Research output: Contribution to journal › Article › Research › peer-review
- Published
Enhanced mechanical properties of Al2O3-C refractories with silicon hybridized expanded graphite
Wang, Q., Li, Y., Jin, S., Sang, S., Xu, Y., Xu, X. & Wang, G., 2 Jan 2018, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 709, p. 160-171 12 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
Environmental hydrogen embrittlement associated with decohesion and void formation at soluble coarse particles in a cold-rolled Al–Cu based alloy
Safyari, M., Moshtaghi, M. & Kuramoto, S., 9 Jul 2020, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing.Research output: Contribution to journal › Article › Research › peer-review
- Published
Erratum to "On the experimental characterization of crystal plasticity in polycrystals"
Tatschl, A. & Kolednik, O., 2004, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. A 364, p. 384-399Research output: Contribution to journal › Article › Research › peer-review
- Published
Evaluation of tensile and low-cycle fatigue properties at elevated temperatures in piston aluminum-silicon alloys with and without nano-clay-particles and heat treatment
Azadi, M., Bahmanabadi, H., Gruen, F. & Winter, G., 11 May 2020, In: Materials Science and Engineering A. 788.2020, 24 June, 16 p., 139497.Research output: Contribution to journal › Article › Research › peer-review
- Published
Evolution of misorientation distribution during warm 'abc' forging of commercial-purity titanium
Mironov, S. Y., Salishchev, G. A., Myshlyaev, M. M. & Pippan, R., 2006, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 418, p. 257-267Research output: Contribution to journal › Article › Research › peer-review
- Published
FIB damage of Cu and possible consequences for miniaturized mechanical tests
Kiener, D., Motz, C., Rester, M., Jenko, M. & Dehm, G., 2007, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 459, p. 262-272Research output: Contribution to journal › Article › Research › peer-review
- E-pub ahead of print
Friction welding of selective laser melted Ti6Al4V parts
Prashanth, K. G., Damodaram, R., Maity, T., Wang, P. & Eckert, J., 3 Aug 2017, (E-pub ahead of print) In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. 704.2017, September, p. 66-71 6 p.Research output: Contribution to journal › Article › Research › peer-review
- Published
General Concept for a Stability Analysis of a Planar Interface under Rapid Solidification Conditions in Multicomponent Alloy Systems
Ludwig, A. & Pustal, B., 2001, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 337-340Research output: Contribution to journal › Article › Research › peer-review
- Published
Generalised ‘Jackson-Hunt’ Model for Eutectic Solidification at Low And Large Peclet Numbers And Any Binary Eutectic Phase Diagram
Ludwig, A. & Leibbrandt, S., 2004, In: Materials science and engineering: A, Structural materials: properties, microstructure and processing. p. 540-546Research output: Contribution to journal › Article › Research › peer-review
